Using wire arc, plasma, and HVOF spraying

At first glance, thermal coating processes create a protective shield that makes a component resistant to thermal, chemical, or mechanical attacks such as wear or corrosion at critical points. What distinguishes thermal spraying from other processes is that the sprayed layer does not simply lie on the surface structure of the component – rather, it clings to it.

  • Thermal spraying technologies

    With thermal spraying, protective coatings are applied to surfaces in order to protect them against external influences such as corrosion or wear. In this way, components can meet several requirements at once – for example, they can withstand not only corrosion attacks but also abrasive stresses. Some components are also able to extend their field of application thanks to the coating. That is why thermal spraying has become a key technology in many industries.

    Diagram with thermal spraying technologies in comparison (particle temperature / particle velocity) by SMS group
  • Wire arc spraying

    For corrosion protection, durability, and wear resistance

    The right corrosion protection is the alpha and omega when it comes to the durability and wear resistance of the material used. With wire arc spraying solutions from SMS group, you benefit from a process characterized by high application rates and low energy consumption.

    Wire arc spraying represents a well-established thermal spray technology. In the process, two metallic wires (feedstock material) are fed into a focus point, where an electric arc melts the wire tips. Droplets are formed and are accelerated into the direction of the substrate by secondary atomization with a high-kinetic gas jet. The atomized particles form a fine-structured homogenous coating on the substrate, with excellent mechanical properties.

  • Plasma spraying

    Efficient coating of surfaces

    Plasma spraying is a thermal coating process based on a superheated gas – known as a plasma. The gases argon, nitrogen, hydrogen, or helium flow between a tungsten cathode and water-cooled copper anode. Between the two electrodes an electric arc is initiated by a high-frequency discharge and then sustained with DC power. The arc ionizes the gas, creating a high-pressure gas plasma. This results in an increase in gas temperature, which can exceed 30,000 °C and expands the volume of the gas, and increases its pressure and velocity as it exits the nozzle.

    Usually, powder is introduced into the gas stream – either just outside the torch or in the diverging exit region of the nozzle. The powder velocities usually achieved in plasma spray deposition range from about 300–460 m/s. Temperatures are usually at or slightly above the melting point. Generally, higher particle velocities and temperatures above the melting point, but without excessive superheating, yield coatings with the highest densities and bond strengths.

    Plasma spraying done in an inert atmosphere and/or low-pressure chamber has become a widely accepted practice, particularly in the aircraft engine industry.

    Plasma spray systems have proven to be an effective means for applying complex, hot corrosion-resistant coatings of the types Ni-Co-Cr-Al-Y to high-temperature aircraft engine components without oxidation of the highly reactive constituents. In fact, plasma spraying can be used to produce coatings of virtually any metallic, cermet, or ceramic material.

  • HVOF spraying

    High-Velocity Oxyfuel (HVOF)

    The high-velocity oxyfuel (HVOF) process distinguishes between gas and liquid fuel applications. In the first case, fuel (propane, propylene, or hydrogen) is mixed with oxygen and burned in a chamber. The second uses liquid kerosene as a fuel and air as an oxidizer. In addition, combined gas and liquid fuel applications are available.

    In both cases, the products of combustion expand through a nozzle, where the gas velocities can become supersonic. Powder is introduced into the nozzle and is heated and accelerated, achieving velocities between 350 and 700 m/s.

    HVOF processes can produce coatings of virtually any metallic or cement material and, for some HVOF processes, most ceramics. Those few HVOF systems burning acetylene as a fuel are necessary to apply the highest-melting-point ceramics such as zirconia or some carbides.

    HVOF coatings have primarily been used for wear resistance to date, but their field of application is expanding.

  • Wire arc spraying equipment

    We bring together two promising technologies: wire arc spraying and an all-digital current/voltage source developed in-house, resulting in the thermal arc spray system PERFECT spray® − consisting of three main components:

    • Arc spraying source – PERFECT spray®
    • Arc spraying gun – PERFECT jet®
    • Wire feed unit – PERFECT drive spray (compact)

    Moreover, our portfolio also covers entire plants and tailor-made transportation systems as complete and automated solutions for your individual project.

  • PERFECT spray®

    The all-digital arc spraying source

    With the wire arc spraying system for thermal spraying according to DIN EN ISO 14917, SMS group opens up entirely new markets in the areas of corrosion and wear protection as well as for maintenance. Through new approaches in electric arc control as well as an open linear design, significant improvements in process efficiency and layer quality can be achieved.

    PERFECT spray® uses a digital power source instead of thyristor current sources. The result is an arc that reacts fast and can be precisely controlled at any time. The system is also characterized by less overspray due to low voltages at both the lowest and highest currents. All in all, using PERFECT spray® customers achieve 25 percent higher efficiency due to reduced wire, air, and energy consumption as well as reduced emissions.

    Moreover, the power source ensures safety in progress in terms of Industry 4.0 as each value can be read out, documented, and controlled – in a material-specific way.

    Arc spraying source models:

    • PERFECT spray® 401 – the all-rounder among the arc spraying sources
    • PERFECT spray® 2000 – the arc spraying source for thick wires and high power
  • PERFECT jet®

    Coating gun

    PERFECT jet® coating gun comes with an innovative jet nozzle concept to generate straightened atomized air for higher efficiency. Its low wear and consistent electrical contact of wires provides for a smooth spraying process. The gun offers superior dependability with a low-maintenance concept with highly functional and durable materials used for all components.

    Arc spraying gun models:

    • PERFECT jet 401 – the perfect partner for the arc spraying source PERFECT spray® 401
    • PERFECT jet 2000 – the perfect partner for the arc spraying source PERFECT spray® 2001
    Spraying gun PERFECT jet® by SMS group for wire arc spraying process
  • PERFECT drive spray (compact)

    Wire feed unit

    Our wire feed unit is available in two different versions: PERFECT drive spray and PERFECT drive spray compact. Both wire feed units offer the flexibility to use wires from all available spool types due to its multipurpose wire dispenser. Each wire is equipped with a 4-wheel drive with a center clamping device for evenly spread adjustable contact pressure. 

    Wire feed unit:

    PERFECT drive spray – the wire feed unit that assures perfect spraying quality through a continuous wire feed

    Wire feed unit PERFECT drive spray by SMS group
Let's get in touch!

Use our contact form for questions, inquiries or personal contact.

  • Plasma spraying equipment

    SMS group combines power source technology developed in-house with state-of-the-art process and gas control to operate single- and multi-cathode plasma torches.

    The portfolio covers process equipment for plasma systems including the power source PERFECT plasma®, gas control, powder conveyors, and others for single-cathode or three-cathode torches – e.g. F4, Plasjet, Axial 3.

  • PERFECT plasma®

    Power source technology for maximum flexibility

    Plasma power source (current in A /voltage in V)

    PERFECT plasma® 400/80

    PERFECT plasma® 600/80

    PERFECT plasma® 800/80

    PERFECT plasma® 1,000/80

    PERFECT plasma® 500/200

    PERFECT plasma® 600/200

    PERFECT plasma® 1,200/120

    PERFECT plasma® 2,000/80

    PERFECT plasma® 3,000/80

    PERFECT plasma® 750/200

    PERFECT plasma® 500/370

  • HVOF spraying equipment

    SMS group offers the complete process equipment for HVOF (High-Velocity-Oxygen-Fuel) and HVAF (High-Velocity Air-Fuel) coating processes.

  • PERFECT hvof®

    Stable HVOF coating process

    PERFECT hvof® describes the complete process equipment necessary for a stable HVOF coating process. The equipment consists of the process control, a gas control (mass flow controlled), a kerosene control, and a cooling water control as well as a safety system.

    PERFECT hvof® is designed to operate HVOF (High-Velocity-Oxygen-Fuel) and HVAF (High-Velocity Air-Fuel) spraying guns. In contrast to classical HVAF systems using compressed air, nitrogen is used to generate artificial compressed air. Different spray guns have different requirements for the plant technology.

    The equipment supports the following spray guns:

    • JP 5000 – pure kerosene spray gun
    • PERFECT jet® 1 (CJS K5.2) – hybrid spray gun (kerosene + hydrogen)
    • PERFECT jet® ID1 (ID-red) – hybrid spray gun (kerosene + hydrogen)
    • ID-mono – hybrid spray gun (kerosene + hydrogen)
    • ID-cool – hybrid spray gun (kerosene + hydrogen)
  • Powder dosage and feeding unit

    The powder dosage and feeding unit (PDFU) by SMS group dosages the powder by means of exchangeable conveyor discs and transports it into a carrier gas. This carrier gas transfers the powder to the spray gun.

    The PDFU disc is able to dosage and feed metallic powder and cermets in a size range from 1 to 150 µm.

    We offer single and twin systems. A twin system consists of two powder hoppers. The powder hopper size is a maximum of 10 liters.

Let's get in touch!